Utah well drilling cost

Cost to Drill a Well in Utah

Nationwide, residential well drilling runs about $21 to $42 per foot for the hole and casing, and a complete private water system commonly totals $5,000-$15,000. Local depth data for Utah is limited, so this page leans on national rates - use it as a starting point, then get local quotes.

Reviewed byDrillerDB Editorial TeamLast updated July 9, 2026

Avg depth: varies
Water wells: 12
U.S. $/ft: $21-42

Typical U.S. well drilling rates by depth

These are national average residential rates for the drilling and casing, not Utah-specific prices. Rates fall into depth bands, with a setup (mobilization) fee on top. Use them as a yardstick, then get local quotes.

Well depth	Drilling + casing (per ft)	Setup fee
Up to 100 ft	$28 - $42	$400 - $600
101-300 ft	$24 - $36	$400 - $600
301-600 ft	$25 - $30	$750 - $800
601 ft and deeper	$21	$1,000

National residential rate model, drilling and casing only. Higher per-foot rates apply to larger casing and hard-rock drilling. Pump, pressure tank, treatment, and permits are separate (see below).

What Utah well records actually show

Cost follows depth, so the most useful Utah number we have is the real one: our database holds 12 water-well records across Utah. The confirmed water-well sample here is too small to state a reliable average depth, so lean on a local driller's read of nearby records. These are real construction records you can review before you hire.

Water wells

Avg depth

n/a

Water table

varies

Check your address depth Explore Utah well records

Beyond the hole: the complete water system

The drilled hole and casing are only part of the bill. A working well also needs a pump and pressure tank, wiring and a pitless adapter, a sanitary cap and grouting, water testing, and often treatment for hardness, iron, or bacteria. Add it up and a complete private well system commonly runs $5,000-$15,000 for Utah, based on our state cost research, versus $5,000-$15,000 nationwide. The low end is a shallow well with simple equipment; the high end is a deep well with treatment and difficult access. A typical Utah project takes 2-4 months from planning to usable water.

What drives the cost of a well in Utah

Depth
The biggest lever. Because drilling is priced largely per foot, a deeper well costs proportionally more. Local records set the expectation.
Geology and casing
Hard rock drills slower and can push per-foot rates toward the high end. Loose or caving formations need more casing, which adds material cost.
Water table and yield
Wells are drilled well past the first water to reach a dependable, year-round aquifer. A low-yield zone can mean drilling deeper.
Pump, tank, and treatment
The pump, pressure tank, and any treatment for hardness, iron, or bacteria are a large share of a complete system - often several thousand dollars.
Permits and testing
Utah: Water right required. Permit, inspection, and water-test fees are usually modest but affect the timeline.
Site access
A rig needs room to work. Tight lots, long driveways, steep grade, or remote sites raise mobilization and labor.

Well drilling cost FAQ for Utah

Cost tracks depth, geology, and casing. Nationwide, residential drilling runs about $21 to $42 per foot for the hole and casing, and a complete private water system (pump, pressure tank, treatment, permits) commonly totals $5,000-$15,000. We hold limited depth data for Utah, so ask two licensed local drillers for written quotes to pin down your number.

Typical U.S. residential rates run about $21 to $42 per foot for drilling and casing, with the lower end on shallow, small-casing wells and the higher end on shallow large-casing or hard-rock work. Most drillers also charge a setup or mobilization fee of a few hundred dollars. These are national averages, not Utah-specific prices - your driller's rate depends on local rock and rig.

Permitting in Utah: Water right required (Utah Code Section 73-3-25). Permit and inspection fees are usually a small part of the total, but they affect the timeline. A licensed Utah contractor typically pulls the permit and folds it into the quote.

The drilled hole and casing are only part of it. A working system also needs a pump and pressure tank, wiring and a pitless adapter, a well cap and grouting, water testing, and often treatment for hardness, iron, or bacteria. Those add several thousand dollars on top of the drilling, which is why a complete private well system commonly runs $5,000-$15,000.

More Utah well resources

Utah Well Drillers

Browse licensed, insured drilling and pump contractors serving Utah and request quotes.

Find drillers

Water Table Depth

Free tool: enter any Utah address to see the likely water table and typical well depth from real nearby wells.

Look up depth

Utah Well Owner Guide

Costs, permits, timeline, water quality, and maintenance for private wells in Utah.

Open guide